SMS connector plug-in

SMS connector is a mobile app that connects the mobile phone and RPA. Its main function is to obtain the SMS verification code received by the mobile phone.

Attention (important)

1. You need to combine the & ldquo; in the factory; Get SMS & rdquo; Use with components;

2. At present, APP only supports installation on Android phones, such as Huawei, Xiaomi and oppo, and only supports obtaining verification code SMS content;

3. In fact, RPA's factory, BOT and commander can obtain mobile phone verification code SMS through SMS connector.

1、 Installation instructions

Step 1:Use the Android mobile browser to open the following link to download the app, or use the browser to scan the code to download the app.

https://justice-bxh.oss-cn-hangzhou.aliyuncs.com/runnerCheck/others/ii-sms-check-0.8.apk

 

Step 2:After downloading, click the Install button to start the installation program; After installation, when opening the connection program, you need to obtain the permission of mobile phone storage space and SMS reading and receiving permission (as shown in the figure below). Click agree to open and use the SMS connector.

Step 3:Make sure the permission is turned on. Enter the connector main page and click more in the upper right corner to check whether the permission of the app is turned on (Figure 1). If it is not turned on, please open it manually and keep it in the state shown in Figure 2;

Step 4:Ensure that the security protection of the verification code in the SMS of the mobile phone system is turned off (Figure 1). In addition to the permission of the connector to remain turned on, the security protection permission of the verification code of the SMS of the Android mobile phone system needs to be turned off, and the protected verification code factory cannot be obtained. Operation steps: turn on the system SMS - & gt; Settings - & gt; Verification code security protection (off). The setting location of different systems is different. Please find the setting location according to your mobile phone system.

2、 Instructions for use

Step 1:Add & ldquo; through factory; Get SMS & rdquo; After the component arrives in the editing area, the number of SMS messages, SMS keywords and SMS content can be set in the component attribute area. At present, only SMS with verification code can be obtained, and all contents of SMS can be obtained or only verification code can be obtained.

Step 2:The premise of normal acquisition is that the mobile phone has installed connector app and is in normal connection status.

Factory and BOT on the computer can obtain verification code SMS through SMS connector;

The SMS connector on the mobile phone supports three connection modes: LAN connection, USB connection and z-commander connection.

1. LAN connection mode

• LAN connection: refers to mobile phones with connectors installed and need to obtain verification code SMS and use factory & amp; BOT computer receiving verification code SMS is under the same Internet. If the mobile phone and computer are in the same place, you can connect the mobile phone and computer to the same WiFi to ensure the SMS connector and factory & amp; BOT is in the same LAN.

• Steps:Open the installed SMS connector to enter the main page, click LAN connection to enter the connection page, enter the required LAN IP and click connection.

• LAN IP:The IP address needs to be the IPv4 of the computer. Query the computer IP method: open the computer operation window, enter CMD to run, then enter ipconfig in the window, and press enter to view the IP address corresponding to the IPv4 of the computer.

2. USB connection mode

• USB connection:It means that the mobile phone and the computer are connected through the USB cable. The mobile phone needs to turn on the USB debugging mode. After the connection is successful, it can be connected through factory & amp; BOT obtains the verification code SMS of the mobile phone, which is suitable for using the connector to obtain the verification code SMS without network environment.

• Steps:The mobile phone and the computer are connected through USB. The mobile phone turns on the USB debugging mode, opens the installed SMS connector to enter the main page, click USB connection to enter the connection page, and then click connection.

• Huawei mobile phoneEnable USB debugging settings: you can; Settings & rdquo-& gt; & ldquo; About mobile phones & rdquo-& gt;& ldquo; Version information & rdquo; Click multiple times to open the developer mode, and then return to & ldquo; Settings & rdquo-& gt;& ldquo; System & rdquo-& gt;& ldquo; Developer options & rdquo-& gt;& ldquo; Debugging & rdquo; Turn on USB mode setting.

• Oppo mobile phoneTurn on USB mode setting: you can set it in & ldquo; Settings & rdquo-& gt; & ldquo; About mobile phones & rdquo-& gt;& ldquo; Version information & rdquo; Find & ldquo; Version number & rdquo; Click 4 times to open the developer mode, and then return to & ldquo; Settings & rdquo-& gt;& ldquo; Other settings & rdquo-& gt;& ldquo; Developer options & rdquo-& gt;& ldquo; Debugging & rdquo; Turn on USB mode setting.

• Mi phonesEnable USB debugging settings: you can; Settings & rdquo-& gt; & ldquo; My device & rdquo-& gt;& ldquo; All parameters & rdquo; Find & ldquo; Version number & rdquo; Click multiple times to open the developer mode, and then return to & ldquo; Settings & rdquo-& gt;& ldquo; More settings & rdquo-& gt;& ldquo; Developer options & rdquo-& gt;& ldquo; Debugging & rdquo; Turn on USB mode setting.

3. Z-commander connection mode

• Z-commander connection:It refers to that the SMS connector transmits the required mobile phone verification code SMS to z-commander through a secure data queue, factory & amp; BOT then obtains the SMS verification code from the z-commander through the queue. Using this connection method, you need & ldquo; Get SMS & rdquo; Component opens the commander connection.

• Steps:& ldquo; in factory; Get SMS & rdquo; Set the commander connection property of the component to on, then open the installed SMS connector to enter the main page, click z-commander connection to enter the connection page, enter the correct URL, key, secret and queue name, and click Connect.

• URL：Enter the link of z-commander. Both local deployment and SaaS services are supported. The SaaS service link address is displayed by default.

• KEY/Secret：It refers to the key value and key encrypted during the transmission of SMS content, which is used to ensure the security and confidentiality of information. This information can be viewed in the key information in the basic settings of z-commander system. An organization has only one corresponding key information.

• Queue name:It refers to the queue flag for receiving message content. Queues can be added, deleted and modified in queue management in z-commander. Each queue has a name, and the queue name cannot be repeated under the current organization.